Advanced Fiber Optic Prep Kit (TK-179)

Ships direct from the manufacturer. Please allow up to 10 business days, though it often ships sooner.

The Jonard Tools TK-179 is the advanced fiber prep kit in a case: eighteen tools for opening, slitting, ringing, stripping, and cutting fiber optic cable, in a rugged 21-pocket tool case that keeps each one in its place. The cable access side is broad. Four mid-span slit and ring tools cover 1.2 to 12 mm, a cable slit and ring tool and a round cable strip and ring tool handle jackets, a buffer tube ringer takes tubes to 6 mm, and two microduct cutters open the ducts that blown fiber runs in. The three-hole fiber stripper takes the jacket, buffer, and coating down to the glass, Kevlar shears cut the strength member, and a splicing knife, a 10 to 22 AWG wire stripper, diagonal cutters, long nose pliers, an insulated probe pick, a multi-bit screwdriver, and a zoom flashlight cover the rest of what a closure, a cabinet, or a pedestal asks for. It's the same tool set as the TK-179B backpack kit, with a case instead of a bag for the technician who works out of a van or a shop.

What's in the Kit

• Mid-span slit and ring tools, 1.2 to 12 mm. MS-306 (1.2 to 3.3 mm), MS-316 (2.9 to 6.8 mm), MS-326 (5 to 10 mm), MS-426 (5.8 to 12 mm), for opening a cable sheath between its ends without touching the fibers inside.
• Jacket and buffer tube access. CSR-1575 cable slit and ring tool; CST-1900 round cable strip and ring tool; BTR-6 buffer tube ringer, for tubes up to 6 mm.
• Microduct cutters. MDC-14 microduct tube cutter and MDC-28 microduct cutter, for a square cut on the ducts that blown and pushed fiber runs in.
• Stripping and cutting. JIC-375 three-hole fiber optic stripper, for the jacket, the buffer coating, and the 250 µm coating down to the 125 µm glass; JIC-186 wire and Kevlar cutting shears for the strength member; JIC-1022 wire stripper, 10 to 22 AWG; KN-7 ergonomic cable splicing knife; JIC-2288 8 in high-leverage diagonal cutting pliers; JIC-842 long nose and side cutting pliers.
• General tools. JIC-22035 insulated probe pick for working wires in and out of contacts; SD-61 six-in-one multi-bit screwdriver with Phillips and other bits; FL-2000 LED flashlight with zoom lens.
• H-90 rugged 21-pocket tool case. A pocket for every tool, so a missing one shows before you leave the site.

Where It Fits

It suits splicing crews doing mid-span entries on distribution cable for closures, FTTH and MDU installers opening drop, riser, and distribution cable, blown-fiber and microduct installs where the duct cutters earn their place, data center and campus teams accessing backbone cable at enclosures and trays, technicians who work from a van or a bench and want the kit in a case that stacks, and a company outfitting new fiber technicians with a matched set from one maker.

Good to Know

This is an access and prep kit, not a termination kit: it gets you from an unopened cable or duct to a stripped fiber, and the cleaver, the connector cleaners, the fusion splicer or connector kit, and the test gear come from elsewhere. Pick the slit and ring tool by the cable's outside diameter, and set the depth on a scrap before the first live cut on a cable you haven't opened before; the aim is to cut the sheath and nothing underneath. For a mid-span entry, make the two ring cuts first, then the lengthwise slit between them, and peel the sheath in sections. Ring a buffer tube with the BTR-6 and flex it to snap the tube rather than cutting through, which keeps the blade off the fibers. Cut microduct square with the duct cutter rather than with a knife or side cutters, since a crushed or angled duct end snags the fiber on the way in. The three-hole stripper takes the fiber down in stages, jacket, buffer, coating, with the coating off in short pulls so the glass isn't scored, and Kevlar goes to the shears, which stay sharp on it where ordinary cutters don't. The probe pick and the wire stripper are for the copper and the contacts in a hybrid cable or a powered cabinet; check for voltage before you open anything that may carry it. For the same tools on your back, the TK-179B swaps the case for a backpack.

Specifications

Documentation